Bootloader debugging with GEF

When Haiku’s early boot process is experiencing unknown crashes or faults, it can be extremely difficult to troubleshoot (especially when serial, video, or other i/o devices are non-functional)

It **is** possible to step through the boot of any architecture of Haiku in a debugger if the system boots and the issue can be reproduced in qemu.

This works for any architecture and is *extremely* helpful to trouble early platforms. Linux or Mac OS are requirements. You need a full POSIX environment.

Building Haiku

On most non-x86 platforms, you will need a “kernel” (haiku_loader) and an “initrd” (haiku_floppyboot).

For arm/arm64: "jam -q @minimum-mmc"

Launching Haiku in QEMU

In the example below, we will prepare Haiku arm in QEMU for debugging.

qemu-system-arm -M raspi2 -kernel haiku_loader.u-boot -initrd haiku-floppyboot.tgz.u-boot -serial stdio -m 2G -dtb rpi2.dtb -s -S

**Key Flags:**

• **-s**

• Shorthand for -gdb

tcp::1234

, i.e. open a gdbserver on TCP port 1234.

• **-S**

• Do not start CPU at startup (you must type ‘c’ in the monitor).

These simple flags will make qemu listen for a debugger connection on localhost:1234 and have the VM not start until you tell it to.

In the example above, we are Emulating a Raspberry Pi 2, and using our Raspberry Pi 2 dtb. If you don’t have a dtb for the machine you’re emulating, you can dump qemu’s internal dtb by adding "-M dumpdtb=myboard.dtb" to the end of your qemu command.

Attaching GEF

GEF

is an enhanced debugger which works extremely well for debugging code running in virtual machines. It piggy-backs on gdb and offers a lot of valueable insight at a glance without requiring to know every gdb command.

Once GEF is installed, we can step through the process to attach gdb to qemu.

Open gdb with our symbols.

First we run gdb pointed at our boot loader. We use the native ELF binary as that seems to give gdb/gef the most accurate knowledge of our symbols. (the haiku_loader.u-boot is wrapped by u-boot’s mkimage, your milage may vary based on platform)

"gdb objects/haiku/arm/release/system/boot/u-boot/boot_loader_u-boot"

Set the architecture

This may not be required, but re-enforces to gef/gdb that we’re working on arm.

"set architecture arm"

Connect to QEMU

Now we tell gdb/gef about out running (but paused) QEMU instance.

"gef-remote -q localhost:1234"

A successful connection should occur.

Step into debugging

Before you begin execution, it’s handy to set a *breakpoint*. A *breakpoint* tells gdb/gef where it should pause execution to begin the debugging process. All of our bootloaders start in a "start_gen" function, so this is a good place to start.

"breakpoint start_gen"

Now that a breakpoint is defined, lets run the virtual machine.

In gef, type "continue".

If everything is working as expected, you should now be “paused” at the "start_gen" function (hopefully showing the C/C++ code).

Now, you have a few commands to leverage:

• **step**

• Take a single step forward and execute the code listed.

• Does **not** step “into” functions, just over them getting the return from the code.

• Alias: s

• **stepi**

• step forward “into” the next code.

• If you’re on a function it will enter the function and show the code executed.

• **break**

• add additional “breakpoints” where you can step through the code execution.

• **continue**

• Resume execution.

• If you have no additional breakpoints the code will “go do what it’s supposed to”

• Alias: c

• **next**

• Resume execution until it reaches the next line of code.

• Useful for example to run until a loop is completed, and stop at the first line after that loop.